雕刻機無線手輪WHB03手搖脈沖發生器 數控系統 手脈 說明書
The Manual For Fully functional Wireless Handle for Engraving machine
Model:WHB03
版本號(Version): V1.0
一. 外觀結構說明 (Structure Description)

備注:當低壓指示燈亮的時候,表示電池電量快用完了,建議更換電池。
Note:When the Low voltage indicator LED light;the battery is completely;Proposed to replace the battery
二. 裝箱配件說明 (Packing Parts)
1.接收器(Wireless USB Receiver):1只(one )
2.無線手柄(Wireless Handle):1只(one )
3.說明書(Manual):1份((one )
三. 直流電氣特性(DC Description)
| 產品名稱 Name | 工作電壓 Voltage | 工作電流 Current | 備注 Note |
無線USB接收器 Wireless USB Receiver | 4.5V—5.0V | 小于 50MA Less than 50MA | |
無線手柄 Wireless Handle | 1.5V—3.0V | 平均電流小于2MA Average Current Less than 2MA | 2000MAH的2節電池能使用2個月 Use of time More than 2 months USE Two 2000MAH Battery |
注意: 無線手柄采用2節AA高容量電池. 當低壓指示燈亮的時候,表示電池電量快用完了,建議更換電池。
Note: Wireless Handle Need Two AA Battery;When the Low voltage indicator LED light;the battery is completely;Proposed to replace the battery )
| 序 號 No | 性能參數描述 Performance or Parameters Description |
| 1 | 采用2.4G無線RF傳輸技術,發射功率0DB,接收靈敏度-98DB The RF is Standard with 2.4G ISM ,the Tx power is 0DB and the RX sensitivity is -98DB |
| 2 | 具有64個跳頻頻道,每個頻道間隔1MHZ The RF has 64 channels,the channel gap is 1Mhz |
| 3 | 空曠直線傳輸距離大于15米 The transmission distance is further than 15 meters with no barrier |
| 4 | 智能無線技術,實現自動跳頻,自動節約功耗,自動ID碼學習 The protocol Designed with high performance; Low power consumption;Automatic learning ID Number |
| 5 | 采用跳頻傳輸,抗干擾能力強;能自動避開無線路由器,2.4G無線耳機,藍牙設備的干擾。 To jump frequency Adaptively when noised ,which can work with 2.4G wireless Mic ,Wlan and Bluetooth etc. devices |
| 6 | 跳頻傳輸技術,同一個房間,能支持32套設備,同時使用,相互不受影響 32 sets Wireless Handle work fine at the same time in one room ,with no-interference each other |
五. 操作使用步驟說明(Use the steps Description)
第1步: (Step 1)
安裝驅動:將光盤放入光驅,安裝無線手柄的驅動,按照電腦提示,直到安裝成功,并結束安裝。
Set up the Driver Software ,and flished Set up:
Please send CD into the CD-ROM;Please follow the computer prompts, Set up the Driver
Software Until flished Set up

鼠標雙擊圖標,開始安裝驅動
Double click the icon to begin installing the driver

按照安裝提示,直到驅動安裝完成
Please follow the computer prompts, Set up the Driver Software Until flished Set up
第2步:(Step 2)
打開軟件:打開剛剛安裝的驅動軟件,然后再打開數控系統軟件NcStudio
OPEN The Driver Software,then Open The NcStudio Software

從開始菜單里邊打開剛剛安裝的驅動
From the Start menu to open just installed the driver inside

打開驅動后,在任務欄會出現驅動運行的圖標
Open the driver soft, will appear in the task bar icon。
第3步:(Step 3)
將無線USB接收器,插入電腦的USB接口。如果是第1次使用,電腦會提示找到新硬件設備......等待USB驅動自動加載成功。
Please Insert Wireless USB Receiver into USB Jack
If this is the 1st use, the computer will be prompted to find a new hardware device;Automatically install the USB driver to wait for success
第4步:(Step 4)
將無線手柄安裝上2節AA電池,注意電池的正負方向,不能裝錯。然后,按下紅色電源開關,LCD將顯示正常,手柄開始正常工作。
Installing 2 AA Batteries into Wireless Handle;Press red Power switch;LCD will display properly, the handle started to work
Note:The battery positive and negative direction, can not install the wrong
六. 使用功能描述(Features Description)
A.按鍵功能描述(Button Features Description) 
B.窗口顯示描述(LCD Display Features Description)
坐標值顯示窗口:(Coordinates of the window)


進給和轉速顯示窗口 :(Feed and speed display window) 
C. 按鍵功能描述
Key function description
對應圖標 Corresponding icon | 名稱 Name | 按鍵功能描述(Key function description) |
 | 停止按鈕 Stop button | 按下該鍵,停止機床。如果機床不能停止,長按下3秒,復位運動控制器,機床停止。 Press the button to stop machine; If the machine does not stop, long press for 3 seconds, reset the motion controller, the machine stops |
 | 開始/暫停按鈕 Start / Pause button | 機床處于運行狀態,按下該鍵,機床暫停加工 機床處于暫停狀態,按下該鍵,機床繼續運行 Machine is running, press the button, the machine to suspend processing Machine is paused, press this button, the machine continues to run |
 | 斷點繼續按鈕 Breakpoint Continue button | 用于機床斷電或斷刀,重上電后,按下該鍵,機床從斷點處繼續工作 Power or cutting knife for machine tools, heavy power, press the button, the machine continues to work from the breakpoint |
| 浮動對刀開始/停止按鈕/復位按鈕 Floating on the knife start or stop or reset Button | 當按下該鍵,機床執行對刀操作:同時,YES和NO提示燈閃爍,需要用戶再次確認是否需要進行對刀。如果按下YES鍵,則開始對刀,LCD的對刀圖標閃爍;表示正在進行對刀操作。按下NO,則退出對刀。 當機床處于加工運行狀態下,按下該按鈕,機床復位,停止加工 When you press the button, the machine Operating the knife YES and NO LED flashing lights, requires the user to reconfirm the need for the knife; If you press YES key, the start of the knife, LCD's on the knife flashing; said the ongoing Operating of the knife. Press NO, then exit to the knife When the machine is processing running, press the button, the machine reset, and stop processing |
 | 回工件原點按鈕 Back to the origin Button | 按下該鍵,機床執行回工件原點操作 Press this key piece back to the origin of the implementation machine |
 | X分中按鈕 X Coordinates 1 / 2 Button | 將X工件坐標分中 X Coordinates 1 / 2 |
 | Y分中按鈕 Y Coordinates 1 / 2 Button | 將Y工件坐標分中 Y Coordinates 1 / 2 |
 | Z**高度設定 Z Coordinates 1 / 2 Button | 將當前Z軸的工件坐標做為Z軸的退刀點 Z Coordinates 1 / 2 |
 | X=0按鈕 X oordinates=0 | Button 將當前坐標設置為X軸工件坐標 X coordinate is set to the current Workpiece coordinates axis |
……
詳情請點擊下載
成都新宏暢無線科技有限公司
www.CDxhctech.com
Chengdu XingHongChang Wireless Technology Co., Ltd
四. 無線性能描述(RF Performance Description